RTL8211（工/商）业级网口芯片bsp自适应修改vivado2019.2
本帖最后由 虫二198 于 2021-3-9 15:11 编辑XILINX官方默认的lwip bsp驱动暂时不支持RTL8211网口芯片，在使用该网口的时候需要自己手动修改库文件以支持该芯片,不同版本工具之间的修改方式大同小异，这边仅以Vitis 2019.2为例。
PS端网口以米联客MZU07A board为例：
Step1：首先，找到vitis ide安装目录下的LWIP库的路径，将其拷贝一份放到工程目录下：Step2：修改lwip211_v1_1\data\lwip211.mld文件（可用Notapad++等编辑器打开），将其中的版本编号
OPTION VERSION =1.1;
修改为
OPTION VERSION = 1.2;;
Step3：打开lwip141_v2_0\src\contrib\ports\xilinx\netif\ xemacpsif_physpeed.c，进行如下修改
根据芯片手册定义Realtek PHY芯片的ID
#define PHY_REALTEK_IDENTIFIER 0x001c
Step4：在get_Marvell_phy_speed库函数基础上，对rtl8211的特殊状态寄存器进行修改，然后保存商业级RTL8211手册PHYSR参数：
static u32_t get_Realtek_phy_speed(XEmacPs *xemacpsp, u32_t phy_addr){ u16_t control; u16_t status; u16_t status_speed; u32_t timeout_counter = 0; u32_t temp_speed;
xil_printf("Start PHY autonegotiation \r\n");
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_AUTONEGO_ADVERTISE_REG, &control); control |= IEEE_ASYMMETRIC_PAUSE_MASK; control |= IEEE_PAUSE_MASK; control |= ADVERTISE_100; control |= ADVERTISE_10; XEmacPs_PhyWrite(xemacpsp, phy_addr, IEEE_AUTONEGO_ADVERTISE_REG, control);
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_1000_ADVERTISE_REG_OFFSET, &control); control |= ADVERTISE_1000; XEmacPs_PhyWrite(xemacpsp, phy_addr, IEEE_1000_ADVERTISE_REG_OFFSET, control);
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, &control); control |= IEEE_CTRL_AUTONEGOTIATE_ENABLE; control |= IEEE_STAT_AUTONEGOTIATE_RESTART; XEmacPs_PhyWrite(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, control);
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, &control); control |= IEEE_CTRL_RESET_MASK; XEmacPs_PhyWrite(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, control);
while (1) { XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, &control); if (control & IEEE_CTRL_RESET_MASK) continue; else break; }
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_STATUS_REG_OFFSET, &status);
xil_printf("Waiting for PHY to complete autonegotiation.\r\n");
while ( !(status & IEEE_STAT_AUTONEGOTIATE_COMPLETE) ) { sleep(1); timeout_counter++;
if (timeout_counter == 30) { xil_printf("Auto negotiation error \r\n"); return XST_FAILURE; } XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_STATUS_REG_OFFSET, &status); } xil_printf("autonegotiation complete \r\n");
XEmacPs_PhyRead(xemacpsp, phy_addr,0x11, &status_speed); /* Commercial RTL8211*/ if (status_speed & 0x400) { temp_speed = status_speed & 0xc000;
if (temp_speed == 0x8000) return 1000; else if(temp_speed == 0x4000) return 100; else return 10; }
return XST_SUCCESS;}
工业级RTL8211手册PHYSR参数：
static u32_t get_Realtek_phy_speed(XEmacPs *xemacpsp, u32_t phy_addr){ u16_t control; u16_t status; u16_t status_speed; u32_t timeout_counter = 0; u32_t temp_speed;
xil_printf("Start PHY autonegotiation \r\n");
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_AUTONEGO_ADVERTISE_REG, &control); control |= IEEE_ASYMMETRIC_PAUSE_MASK; control |= IEEE_PAUSE_MASK; control |= ADVERTISE_100; control |= ADVERTISE_10; XEmacPs_PhyWrite(xemacpsp, phy_addr, IEEE_AUTONEGO_ADVERTISE_REG, control);
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_1000_ADVERTISE_REG_OFFSET, &control); control |= ADVERTISE_1000; XEmacPs_PhyWrite(xemacpsp, phy_addr, IEEE_1000_ADVERTISE_REG_OFFSET, control);
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, &control); control |= IEEE_CTRL_AUTONEGOTIATE_ENABLE; control |= IEEE_STAT_AUTONEGOTIATE_RESTART; XEmacPs_PhyWrite(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, control);
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, &control); control |= IEEE_CTRL_RESET_MASK; XEmacPs_PhyWrite(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, control);
while (1) { XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_CONTROL_REG_OFFSET, &control); if (control & IEEE_CTRL_RESET_MASK) continue; else break; }
XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_STATUS_REG_OFFSET, &status);
xil_printf("Waiting for PHY to complete autonegotiation.\r\n");
while ( !(status & IEEE_STAT_AUTONEGOTIATE_COMPLETE) ) { sleep(1); timeout_counter++;
if (timeout_counter == 30) { xil_printf("Auto negotiation error \r\n"); return XST_FAILURE; } XEmacPs_PhyRead(xemacpsp, phy_addr, IEEE_STATUS_REG_OFFSET, &status); } xil_printf("autonegotiation complete \r\n");
XEmacPs_PhyRead(xemacpsp, phy_addr,0X1A, &status_speed); /* Industrial RTL8211 */
if (status_speed & 0x04) { temp_speed = status_speed & 0x30;
if (temp_speed == 0x20) return 1000; else if(temp_speed == 0x10) return 100; else return 10; }
return XST_SUCCESS;}
Step5：在vitis软件中导入修改后的lwip库的路径（需根据实际情况更改此路径，若不更改将产生错误）
Step6：导入库文件后重启SDK
Step7: 勾选lwip库文件
Step8: 选择lwip211_1.2版本
Step9: 选择File->New->Application Project->lwip_echo_serverStep10:右击lwip_testàDebugAsà DebugConfigurations,然后单击debugStep11:单击运行，查看输出结果
PL端网口以米联客MA703_100T为例
Xilinx SDK 目录下面 xaxiemacif_physpeed.c 文件里面对 PHY 芯片有驱动，目前支持 MARVEL 和 TI 的部分 PHY 芯片，如果使用其他厂家的 PHY 芯片，需要更改驱动，否则协商不能通过。打开fpga_prj\uisrc\07_sdk_src\lwip211_v1_1\src\contrib\ports\xilinx\netif\xaxiemacif_physpeed.c 源文件，增加宏定义
添加PHY ID的定义以下驱动程序的修改仅支持工业级RTL8211的千兆协商
unsigned get_IEEE_phy_speed(XAxiEthernet *xaxiemacp)
{
u8 phytype;
u16 phy_val;
u16 phy_identifier;
u16 phy_model;
u16 control;
u16 status;
u16 partner_capabilities;
u16 partner_capabilities_1000;
u16 phylinkspeed;
int TimeOut;
#ifdef XPAR_AXIETHERNET_0_BASEADDR
u32 phy_addr = detect_phy(xaxiemacp);
/* Get the PHY Identifier and Model number */
XAxiEthernet_PhyRead(xaxiemacp, phy_addr, PHY_IDENTIFIER_1_REG, &phy_identifier);
XAxiEthernet_PhyRead(xaxiemacp, phy_addr, PHY_IDENTIFIER_2_REG, &phy_model);
/* Depending upon what manufacturer PHY is connected, a different mask is
* needed to determine the specific model number of the PHY. */
if (phy_identifier == MARVEL_PHY_IDENTIFIER) {
phy_model = phy_model & MARVEL_PHY_MODEL_NUM_MASK;
if (phy_model == MARVEL_PHY_88E1116R_MODEL) {
return get_phy_speed_88E1116R(xaxiemacp, phy_addr);
} else if (phy_model == MARVEL_PHY_88E1111_MODEL) {
return get_phy_speed_88E1111(xaxiemacp, phy_addr);
}
} else if (phy_identifier == TI_PHY_IDENTIFIER) {
phy_model = phy_model & TI_PHY_DP83867_MODEL;
phytype = XAxiEthernet_GetPhysicalInterface(xaxiemacp);
if (phy_model == TI_PHY_DP83867_MODEL && phytype == XAE_PHY_TYPE_SGMII) {
return get_phy_speed_TI_DP83867_SGMII(xaxiemacp, phy_addr);
}
if (phy_model == TI_PHY_DP83867_MODEL) {
return get_phy_speed_TI_DP83867(xaxiemacp, phy_addr);
}
}
else {
if (phy_identifier==PHY_REALTEK_IDENTIFIER){
XAxiEthernet_PhyWrite(xaxiemacp, phy_addr, 0x1A, 0x20);
XAxiEthernet_PhyRead(xaxiemacp, phy_addr,IEEE_CONTROL_REG_OFFSET,&control);
control |= IEEE_CTRL_AUTONEGOTIATE_ENABLE;
control |= IEEE_STAT_AUTONEGOTIATE_RESTART;
XAxiEthernet_PhyWrite(xaxiemacp,phy_addr,IEEE_CONTROL_REG_OFFSET,control);
}
if (phy_identifier==PHY_REALTEK_IDENTIFIER){
XAxiEthernet_PhyRead(xaxiemacp, phy_addr, 0, &control);
XAxiEthernet_PhyWrite(xaxiemacp, phy_addr, 0,control | IEEE_CTRL_RESET_MASK);
for(TimeOut=0;TimeOut<5000;TimeOut++);
XAxiEthernet_PhyWrite(xaxiemacp, phy_addr, 0x1A, 0x20);
XAxiEthernet_PhyRead(xaxiemacp, phy_addr, IEEE_AUTONEGO_ADVERTISE_REG, &control);
control |= IEEE_ASYMMETRIC_PAUSE_MASK;
control |= IEEE_PAUSE_MASK;
control |= ADVERTISE_100;
control |= ADVERTISE_10;
XAxiEthernet_PhyWrite(xaxiemacp, phy_addr, IEEE_AUTONEGO_ADVERTISE_REG, control);
XAxiEthernet_PhyRead(xaxiemacp, phy_addr, IEEE_1000_ADVERTISE_REG_OFFSET,&control);
control |= ADVERTISE_1000;
XAxiEthernet_PhyWrite(xaxiemacp, phy_addr, IEEE_1000_ADVERTISE_REG_OFFSET,control);
XAxiEthernet_PhyRead(xaxiemacp, phy_addr, IEEE_CONTROL_REG_OFFSET, &control);
control |= IEEE_CTRL_AUTONEGOTIATE_ENABLE;
control |= IEEE_STAT_AUTONEGOTIATE_RESTART;
XAxiEthernet_PhyWrite(xaxiemacp, phy_addr, IEEE_CONTROL_REG_OFFSET, control);
return 1000;
}
LWIP_DEBUGF(NETIF_DEBUG, ("XAxiEthernet get_IEEE_phy_speed: Detected PHY with unknown identifier/model.\r\n"));
}
设置BSP文件测试
页:
[1]